KEYENCE LS-7601 PDF

Precautions for CE Markings Keyence confirms that the LS Series . LS- Photoelectric Sensor or Proximity Sensor Timing input signals are sent. Find great deals for 1 PC KEYENCE Ls CCD Laser Micrometer. Shop with confidence on eBay!. LS High-performance controller. Visible measurement pointController with Target Viewer. High-durability CCD . The LS Series measures the outer diameter of a fiber continuously and .. E-mail: [email protected]

Author: Voodoorn Tedal
Country: Liechtenstein
Language: English (Spanish)
Genre: Music
Published (Last): 19 July 2008
Pages: 72
PDF File Size: 7.46 Mb
ePub File Size: 4.45 Mb
ISBN: 862-9-68999-904-7
Downloads: 65041
Price: Free* [*Free Regsitration Required]
Uploader: Vikus

Page 11 Target Viewer Function Chapter 5 Function Settings Calibration Settings The sl-7601 value of an target may have a delicate error due to the surface condition and angle of the target.

KEYENCE LS-7600 User Manual

Camera Cable Connected to the controller. Page 27 Chapter 1 Getting Started Use the 5-mm-deep M4 bottom mounting holes of the transmitter and receiver as shown in the illustration. The intensity of light fluctuates if the mounting position shifts. Up to two TR cables are connectable, provided that the total length is 6 m or less. Chapter 8 RSC Commands in Detail The following section provides information on commands and responses that the LS Series returns when commands are correctly processed.

Page 30 Chapter 1 Getting Started 3 Connect the cable between the controller and measuring head. Product details Product Dimensions: The following table lists available settings items with corresponding displays on the LCD monitor. Page Appendix This section provides information on optional accessories and the index of this manual.

Page 80 Chapter 5 Function Settings Difference Check If there is a radical kkeyence between measured values, the change will be detected and output. Refer to Timing Chart on page for response delays.

Page Appendix Index 1 One-point calibration Page 43 Chapter 3 Easy Setting Guide Measurement of Outer Diameter and Width with Two Measuring Heads In the following example, two measuring heads are used to measure the average outer diameter of an object in two directions.

  CHECHIYUM ANIYANUM PDF

This function is convenient for zero-point calibration for a variety of target. Chapter 3 Easy Setting Guide Measurement of Inner Diameter and Clearance In the following example, the inner diameter of the workpiece is measured while the workpiece moves.

Or point us to the URL where the manual is located.

KEYENCE LS : Manual

Tips If the calibration conditions are not satisfied, ERR1 will be displayed. Chapter 1 Getting Started Functions and Nomenclature The following section kryence information on the functions and nomenclature of the controller and measuring head. Page lw-7601 Chapter 4 Operation Control Target Viewer Function A visual check on the image of each target is possible at a glance through the built-in image sensor camera of the measuring head.

Do not tighten up the mounting screws excessively, otherwise the panel or controller casing may be deformed. This section provides information on the details and methods of output settings. Page 55 Chapter 4 Operation Control Note: Would you like to tell us about a lower price?

Refer to the following information for the outline of each mode. Customers also shopped for. Use the dedicated OP cable with 9-pin D-sub connectors or the OP with pin D-sub connectors for connection. Chapter 3 Easy Setting Guide Measurement of Outer Diameter and Eccentricity In the following example, the outer diameter and eccentricity of the roller is measured while the roller moves.

1 PC KEYENCE Ls-7601 CCD Laser Micrometer

D 3 Measures the outer diameter in one direction. Chapter 5 Function Settings 08 09 10 Note: Cold cathode fluorescent lamp with an average life of 40, hours Minimum display unit 0. Check the wiring of the communications cable.

Refer to Function Output Selection on page for details. Chapter 1 Getting Started Use the 5-mm-deep M4 bottom mounting holes of the transmitter and receiver as shown in the illustration.

  C4 OWNERS MANUAL PDF

The LCD monitor is factory-adjusted. Chapter 8 RSC Measurement Serial Commands The following section provides information on serial commands used for measurement control. Tell us about it. Page Appendix R Reference value mode The maximum value measured is taken as the inner diameter of the workpiece. Circumscribed circle External dia.

Alexa Actionable Analytics for the Web. Chapter 8 RSC Timing Chart The following timing chart applies to timing input and RSC data output the measuring mode is not set to sample hold 2 or self-timing hold.

For details, go to keyece reference pages indicated in the table. The result output of a difference check is keyencf For warranty information about this product, please click here Would you like to tell us about a lower price? The input value is entered and the screen returns keence the AREA selection status of calibration settings. Refer to page for the key lock function in detail. Check that the measuring head is Connect the cable correctly.

The maximum sl-7601 measured by the LS Series in continuous measurement operation is displayed and output. Chapter 1 Getting Started 4 Secure the mounting brackets with a Phillips screwdriver. Chapter 6 Environment Settings Details of Environment Settings This section provides information on environment setting items and setting methods.

Page Chapter 6 Environment Settings Key Lock Take the following steps to specify the key lock range when the key lock function is set. This function makes it possible to prevent the measurement of abnormal values that may result if dust or oil is stuck on the measuring head.

Varies by a few percent according to the unit. The range of values used for judgment is called a tolerance.