ASTM B153 PDF

B – 11 Standard Test Method for Expansion (Pin Test) of Copper and Copper- Alloy Pipe and Tubing, copper, copper alloy, expansion, expansion test, pin. This standard is issued under the fixed designation B ; the 1 This test method is under the jurisdiction of ASTM Committee B05 on Copper. Find the most up-to-date version of ASTM B at Engineering

Author: Douktilar Nerisar
Country: Rwanda
Language: English (Spanish)
Genre: Literature
Published (Last): 16 September 2005
Pages: 453
PDF File Size: 16.59 Mb
ePub File Size: 7.76 Mb
ISBN: 682-1-76816-554-9
Downloads: 70161
Price: Free* [*Free Regsitration Required]
Uploader: Dozahn

ASTM B153 – 11(2017)

Screening and resubmittal of samples from rejected lots for visual and dimensional examination is acceptable. Any evidence of leakage shall be cause for rejection. When agreement on the Rockwell hardness tests cannot be reached, the tensile strength requirements of Atm 2 shall be the basis for acceptance or rejection. Rockwell hardness shall be made on the inside surface of the tube.

Standard Specification for Ferromolybdenum. Except as otherwise speci? Dimensions and Permissible Variations Standard Specification for Ferrochromium. Standard Specification for Steel Screw Spikes.

B — 02 Standard Speci? By using this site, you agree to the Terms of Use and Privacy Policy.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Standard Specification for Pearlitic Malleable Iron.

  ILARION FELEA POCAINTA PDF

A withdrawn standard has been discontinued by its sponsoring committee. Standard Specification for Silicomanganese. Ten alloys are speci? When suitable equipment is not available for determining the speci? Standard Specification for Nickel Oxide Sinter. Use equipment for the detection and removal of mercury vapor. The notchdepth tolerance shall be Standard Specification for Ferrotitanium. This may optionally be followed by a dash and the last two digits of the year in which the standard was adopted.

Retrieved from ” https: D Light-drawn and hard-drawn tempers are available in round-tube only. Immediately after removal from the solution, the specimen shall be wiped free of excess mercury and examined for cracks. Lot Size Pieces Per Lot Sample Size 2 to 8 9 to 90 91 to to to to to to 10 10 to 35 Entire lot 8 12 19 21 27 35 38 46 Last previous edition B — Grade B7 Studs bolts and Grade B16 Studs bolts fall in this category and are used for high temperature, high-pressure environments like petroleum industry.

For all other tube no Rockwell hardness values shall apply. The test method used shall provide for easy visual detection of any leakage, such as by immersion of the tube under water or by the pressure differential method.

  CHILDHOOD MEMORY BANDARI PIANO SHEET PDF

Views Read Edit View history. C Although no minimum grain size is speci?

Originally published b15 B — 40 T. A Alloy Designations of Speci? Standard Tube Size, inch Up to and including 3? Rockwell hardness tests shall be made on the inside surface of the tube. Workmanship, Finish, and Appearance Former soft anneal soft anneal light anneal light anneal soft anneal soft anneal light anneal light anneal soft anneal soft anneal up to 0.

ASTM B无缝黄铜管_百度文库

Drawn temper is for general purposes and is most commonly used where there is no speci? The manufacturer shall select the nondestructive test that is most suitable for the tube size and the application. From Wikipedia, the free encyclopedia.

However, if subsequent testing by the b15 establishes that the material does not meet these requirements, the material shall be subject to rejection. The tension test for other sizes of tubes need not be made except when indicated by the purchaser axtm the time of placing the order. A superscript epsilon e indicates an editorial change since the last revision or reapproval.