AIRTRONICS VG6000 MANUAL PDF

GHz FHSS-1 RX 6-Channel Full-Range Receiver Operating Instructions Use this receiver with your Airtronics RDS GHz transmitter or . We appreciate your purchase of this new AIRTRONICS. VG or VG Radio System. These instructions are intended to acquaint you with the many unique. Airtronics/Sanwa VG Modes? Radios. All; Planes; Sailplanes; Helis; FPV; Multirotors; Cars; Boats. About Sanwa VG Here you can.

Author: Durg Mazugal
Country: Serbia
Language: English (Spanish)
Genre: Sex
Published (Last): 19 January 2015
Pages: 134
PDF File Size: 6.98 Mb
ePub File Size: 15.80 Mb
ISBN: 958-1-91351-372-8
Downloads: 52938
Price: Free* [*Free Regsitration Required]
Uploader: JoJolkree

AIRTRONICS VG INSTRUCTION MANUAL Pdf Download.

Airtronics is Distributed Exclusively in North America by: The transmitter will stay in Low Power Mode for 3 minutes. This equipment has been tested in accordance with the. All your setting are saved in a eprom chip that does not need any type of battery to hold its fg6000. The Bind LED on the receiver will continue to blink slowly.

All settings are saved automatically on all models. Any other modifications made to the transmitter other than adjusting stick tension will void any and all warranties covered be Airtronics Inc. By pressing ‘print’ button you will print only current page. If binding the receiver to an Airtronics SDG 2. In addition, the receiver should be wrapped in foam rubber to protect it from vibration.

Airtronics VG Manuals

When you mount the receiver antenna wires, do not bend the reception wires. Alternatively, cut two short pieces of plastic tube and slide one antenna reception vvg6000 into each piece of tube, then tape or glue the tube to your model.

It can be dangerous if you activate the components in reverse order as the servos may start up inadvertently. Also, if response seems slow during use, discontinue use as quickly as possible. Coaxial Cables Reception Wire If mounting inside a carbon fiber fuselage, the antenna reception wires must be run outside of the model as described in the notation below. There is airfronics danger of runaway operation if connectors shake loose during use.

  C.S.LEWIS CARTAS DEL DIABLO A SU SOBRINO PDF

Got it, continue to print. If using the receiver with an Airtronics SDG 2. This will ensure that your model receives control signals no matter what its vvg6000, attitude, or heading. Before use, double-check that the transmitter airtronicz receiver batteries are sufficiently charged.

After use, to prevent any chance of damaging the antenna, the antenna should be moved into the horizontal stowed position. Under no circumstances should the antenna reception wires be mounted parallel to each other.

Airtronics VG6000 (6 channel computer radio)

Failure to mount the receiver antenna wires as described can result in poor reception, or in some cases, complete loss of reception. Don’t have an account? The coaxial cables the thicker portion of the receiver antenna wires can be bent into gentle curves, however, do not bend the coaxial cables acutely, or repeatedly bend them, or the antenna cores can be damaged. You will use two servos on two seprate channels to mix both ailerons and elevator together using only the left and right wing controls.

It’s a community-based project which helps to repair anything. The tubes will protect the antenna reception wires from damage. Always before use, conduct a bench test to ensure airtgonics the servos operate properly. The Trainer system airtronica the VG transmitter allows you to connect any two Airtronics RD series transmitters together for the purpose of training a new pilot. The response speed of the receiver can be affected if used where multiple 2.

Page maunal Additional Receivers that will work with the VG You should set the packaging aside for use if you ever need to send your radio in for service, or to store your radio in case you do not plan to use it for an extended period of time. Unlike frequency bands used with earlier radio control systems, reception with this 2.

By using the Flap to Elevator mix, you can change the way the airtronifs reacts when the flaps are lowered by adding a small amount of down elevator. Also, wire mesh and similar barriers can adversely affect operation.

  ESO NO DE MARCELO BIRMAJER PDF

It has the features available to get the most out of any type of model. Observe any applicable laws and regulations in place at your airtroincs site when vt6000 the 2. REV is available on all channels.

After 3 minutes, the transmitter will revert to Normal mxnual. Your battery is rated at 9. Comments to this Manuals Your Name. When installing the receiver, the antenna reception wires the thin tip at the end of the coaxial cables should not come into contact with any carbon or metal components conductive components.

To adjust stick length, hold Part B with your fingers and unscrew Part A counterclockwise to loosen the two pieces. This is the optimum angle for use.

What differential maunal is actually change the amount of aileron movement percentage between the aileron being in the up position compared to the down position. The receiver is susceptible to airtronjcs and moisture. If there is a problem with servo movement, try moving to a different position while still maintaining the same distance from your model, then check servo movement again. Make sure that the receiver, servo sand switch harness connectors are securely fitted.

Failure to take appropriate measures could result in damage to the receiver. The transmitter is now in Low Power Airtrobics. The Bind LED on the receiver will blink slowly. This receiver operates on the 2.

Add to my manuals Add. Also, conduct a range test at the area of operation to ensure that the radio control system has complete control of the model at the farthest reaches of the operational area. If the throttle stick is not in the low position, when you turn it on, you will hear a continuous beeping sound and the display will read HI.